Veröffentlichungen und Präsentationen

Schnellsuche

Ressourcen

Whitepaper

Sehen Sie, wie die Multiphysik-Simulation in Forschung und Entwicklung eingesetzt wird

Ingenieure, Forscher und Wissenschaftler aus allen Branchen nutzen die Multiphysik-Simulation, um innovative Produktdesigns und -prozesse zu erforschen und zu entwickeln. Lassen Sie sich von Fachbeiträgen und Vorträgen inspirieren, die sie auf der COMSOL Conference präsentiert haben. Durchsuchen Sie die untenstehende Auswahl, verwenden Sie die Schnellsuche, um eine bestimmte Präsentation zu finden, oder filtern Sie nach einem bestimmten Anwendungsbereich.

Sehen Sie sich die Kollektion für die COMSOL Conference 2024 an

Suchbegriff:

COMSOL Multiphysics Modeling for Design Optimization of Eddy Current Crack Detectors

E. Weststrate, M. Steinback, N. Rensing, and T. Tiernan
Radiation Monitoring Devices Inc., Watertown, MA, USA

Passing alternating current through a wire placed just above a conducting surface induces eddy currents in that surface. Any cracks present in the conductor modify the eddy current distribution, creating a magnetic field signature unique to the crack. This magnetic signature can be ... Mehr lesen

Implementation of a Paraxial Optical Propagation Method for Large Photonic Devices

J.E. Toney[1]

[1]Pennsylvania State University Electro-Optics Center, Freeport, Pennsylvania, USA

We demonstrate the use of COMSOL Multiphysics with MATLAB to model signal generation in wide-bandgap semiconductor radiation detectors. A quasi-hemispherical detector design is compared with a simple, planar detector. Results show that the quasi-hemispherical design can simply and ... Mehr lesen

Thermal Design of Power Electronic Devices and Modules

N. Delmonte[1], M. Bernardoni[1], P. Cova[1], and R. Menozzi[1]
[1]Dipartimento di Ingegneria dell’Informazione, University of Parma, Parma, Italy

This work describes a way to apply 3D Finite Element Analysis (FEA) to the thermal design of power electronic modules using simplified geometry models of the system components. The method here presented can overcome the problem of solving equation systems with a very high number of ... Mehr lesen

COMSOL Multiphysics^® as a General Platform for the Simulation of Complex Electrochemical Systems

A. Lavacchi[1]
[1]Department of Chemistry, University of Firenze, Sesto Fiorentino, FI, Italy

Microelectrodes demonstrate that modeling is crucial for understanding the behavior of complex electrochemical systems. The use of the finite element methods in electrochemistry may be of much more general interest for its ability to handle complex geometries. In this context a ... Mehr lesen

Thickness Optimization of a Piezoelectric Converter for Energy Harvesting

M. Guizzetti[1], V. Ferrari[1], D. Marioli[1], and T. Zawada[2]

[1]Dept. of Electronics for Automation, University of Brescia, Brescia, Italy
[2]Meggitt, Ferroperm Piezoceramics A/S, Kvistgaard, Denmark

The conversion of mechanical energy from environmental vibrations into electrical energy is a key point for powering sensor nodes toward the development of autonomous sensor systems. Piezoelectric energy converters realized in a cantilever configuration are the most studied for this ... Mehr lesen

Permanent Magnet Arrangements for Low-Field NMR

C. Horch[1], S. Schlayer[1], and F. Stallmach[1]
[1]Faculty of Physics and Earth Sciences, University of Leipzig, Leipzig, Germany

For low-field NMR (Nuclear magnetic resonance), NdFeB permanent magnet arrangements are proposed to provide the static polarizing magnetic field. Especially a parallel and a circular arrangement of the permanent magnets, iron yokes and small shim magnets were tested and improved by ... Mehr lesen

Numerical Validation of the Efficiency of Dual-Frequency Radiofrequency Ablation

A. Candeo[1] and F. Dughiero[1]
[1]Department Electrical Engineering, University of Padova, Padova, Italy

Radiofrequency Ablation (RFA) represents a valid alternative for treating liver metastases in medically complicated patients. Conventional devices currently operate at 500 kHz, due to good conducting properties of tissues. However, the use of lower frequencies (i.e. 20 kHz) has been ... Mehr lesen

A Finite Element Model for The Axon of Nervous Cells

S. Elia[1], P. Lamberti[1], and V. Tucci[1]
[1]Dept. of Electrical and Information Engineering, University of Salerno, Salerno, Italy

This paper proposes a FEM model for a segment of a nervous cell axon, which takes into account, through the so called Hodgkin-Huxley equations, the non linear and time varying dynamics of the membrane surrounding it. A combination with Maxwell equations is performed in a numerical ... Mehr lesen

Fast 2D Simulation of Superconductors: A Multiscale Approach

V.M. Rodriguez-Zermeno[1], M.P. Sørensen[1], N.F. Pedersen[2], N. Mijatovic[2], and A.B. Abrahamsen[3]
[1]DTU Mathematics, Lyngby, Denmark
[2]DTU Electrical Engineering, Lyngby, Denmark
[3]Materials Research Division, Risø, DTU, Roskilde, Denmark

This work presents a method to calculate AC losses in thin conductors such as the commercially available second generation superconducting wires through a multiscale meshing technique. The main idea is to use large aspect ratio elements to accurately simulate thin material layers. For a ... Mehr lesen

The Acoustoelastic Effect: EMAT Excitation and Reception of Lamb Waves in Pre-Stressed Metal Sheets

R.M.G. Ferrari[1]
[1]Danieli Automation S.p.A., Buttrio, UD, Italy

The acoustoelastic effect relates the change in the speed of an acoustic wave travelling in a solid, to the pre-stress of the propagation medium. In this work the possibility of assessing nondestructively the stress status in metal sheets, by using the acoustoelastic effect, is ... Mehr lesen

Erste

1751–1760 of 1762

Letzte