Menu

Discussion Forum

New Discussion
Filtern

Note: This discussion is about an older version of the COMSOL Multiphysics® software. The information provided may be out of date.

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

Segregated Solver, Segregated group

Posted 20.02.2013, 01:14 GMT-5 Fluid & Heat, Interfacing, Heat Transfer & Phase Change, Computational Fluid Dynamics (CFD), Geometry, Installation & License Management, Materials, Mesh, Modeling Tools & Definitions, Parameters, Variables, & Functions, Results & Visualization, Studies & Solvers Version 4.3a 2 Replies

Nithin
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

What is the meaning of "Segregated Solver" and "Segregated Group"?

While computing for the results, I am getting a line like follows... "Segregated Solver 17% Step 3" .
And the value beside Step in that line is varying between 1, 2 & 3.

Does the step in that line mean "time step"?
As i have a time step of 300 sec spanning from 0 sec to 86400 sec, total 288 step.
So, will need to go through 288 steps??
2 Replies Last Post 20.02.2013, 04:53 GMT-5
Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 20.02.2013, 01:56 GMT-5
Hi

check the doc on the solver. When COMSOL tries to solve a complex multi-physics problem, it can either solve it directly (all variables at a time, or try a segregated group approach (uses less ram but takes longer) by solving (in a loop) for some variables, then using the results to solve for the others. This approach is often better for highly non-linear models too

--
Good luck
Ivar
Hi check the doc on the solver. When COMSOL tries to solve a complex multi-physics problem, it can either solve it directly (all variables at a time, or try a segregated group approach (uses less ram but takes longer) by solving (in a loop) for some variables, then using the results to solve for the others. This approach is often better for highly non-linear models too -- Good luck Ivar
Mattia Montanari
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 20.02.2013, 04:53 GMT-5
Hello,

" Does the step in that line mean "time step"?"
No.
the value Step =[1,2,3] is due to the termination technique you have chosent. it has nothing about time step.
You find more here
model-> study1->Solver config->solver1->time-Depend -> segregated step -> "method and termination"

"So, will need to go through 288 steps??"
No.
Many more. Comsol gives you 288 results (in time for instance), but actually it solves the linear(ized) system many times more!
You find more here
model-> study1->Solver config->solver1->time-Depend ->"output" try to set the "time to store" == 'steps taken by solver'

As Ivar suggested: go through the manual :-)

Hope it helps,
Mattia
Hello, " Does the step in that line mean "time step"?" No. the value Step =[1,2,3] is due to the termination technique you have chosent. it has nothing about time step. You find more here model-> study1->Solver config->solver1->time-Depend -> segregated step -> "method and termination" "So, will need to go through 288 steps??" No. Many more. Comsol gives you 288 results (in time for instance), but actually it solves the linear(ized) system many times more! You find more here model-> study1->Solver config->solver1->time-Depend ->"output" try to set the "time to store" == 'steps taken by solver' As Ivar suggested: go through the manual :-) Hope it helps, Mattia

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content