Veröffentlichungen und Präsentationen

Schnellsuche

Ressourcen

Whitepaper

Sehen Sie, wie die Multiphysik-Simulation in verschiedenen Branchen eingesetzt wird

Multiphysik-Modellierung und -Simulation treiben Innovationen in Industrie und Wissenschaft voran – wie die zahlreichen Anwendungsbeispiele zeigen, die jedes Jahr in den Fachbeiträgen und Postern von Ingenieuren, Forschern und Wissenschaftlern auf der COMSOL Conference vorgestellt werden. Lassen Sie sich von den unten aufgeführten aktuellen Beiträgen inspirieren oder nutzen Sie die Schnellsuche, um eine bestimmte Präsentation zu finden oder nach Anwendungsbereich oder Konferenzjahr/-ort zu filtern.

Sehen Sie sich die Kollektion für die COMSOL Conference 2024 an

Suchbegriff:

Heat Transfer and Phase Change

Using Temperature Signals to Estimate Geometry Parameters in Fractured Geothermal Reservoirs

F. Maier[1], P. Oberdorfer[1], I. Kocabas[2], I. Ghergut[1], M. Sauter[1]
[1]Dpt. Applied Geology, Center of Geosciences, Georg-August-University, Göttingen, Germany
[2]Petroleum and Natural Gas Engineering Department Batman, Batman University, Batman, Turkey

We compare the output of 2D single fracture models as well as analytical solutions of the problem. The temperature signal is evaluated with the heat transfer mode while the flow field is assumed to exhibit Darcy flow everywhere. The problem is time-dependent so we have to take into ... Mehr lesen

Ampacity Simulation of a High Voltage Cable Used in Offshore Wind Farms

E. Pelster[1]
[1]Wenger Engineering, Ulm, Germany

The ampacity of a cable depends on the cross section of its conductor. When selecting a cable design for a specific application it is of interest to choose the lowest possible conductor cross section in order to reduce material costs. Therefore an exact calculation of the ampacity is ... Mehr lesen

Optimization of Thermal Properties Identification of Complex Thin Films Using MATLAB® and COMSOL Multiphysics

N. Semmar[1], B. Wane[1]
[1]GREMI, UMR7344, CNRS-University of Orleans, Orléans Cedex 2, France

The importance of laser processing and thermal properties investigation of bulk materials and thin layers is still increasing. For thermal properties investigation many experimental systems were developed based on the photothermal effect. One of typical ways is to induce a rapid surface ... Mehr lesen

Heat and Mass Transfer in Reactive Multilayer Systems (RMS)

M. Rühl[1], G. Dietrich[2], E. Pflug[1], S. Braun[2], A. Leson[2]
[1]TU Dresden, Laser and Surface Technology, Dresden, Germany
[2]IWS Dresden, Fraunhofer Institute for Material and Beam Technology, Dresden, Germany

Established joining techniques like welding, soldering or brazing typically are characterized by a large amount of heat load of the components. Especially in the case of heat sensitive structures like MEMS this often results in stress induced deformation and degradation or even damaging ... Mehr lesen

Multiphysics Modeling of Spring-Supported Thrust Bearings for Hydropower Applications

F.X. Borràs[1], J. Ukonsaari[2], A. Almqvist[1]
[1]Luleå University of Technology, Luleå, Sweden
[2]Vattenfall Research and Development, Luleå, Sweden

Spring-supported thrust bearings are used in huge rotor dynamic machines, generally to support the shafts from the biggest hydropower generators. Any attempt of modifying yhis type of thrust bearing implies huge investment and is associated with some risks. The goal of the present work ... Mehr lesen

Simulation and Design of an Oven for PET Blow Molding Machines

M. Mor[1], C. Seneci[1], V. Zacché[1], C. Remino[1], G. Petrogalli[1], D. Fausti[1]
[1]Polibrixia, Brescia, Italy

This paper presents the study and design of a new generation oven for PET blow-molding machines. The design faced several technical challenges such as: the temperature distribution in the critical areas, the sharp curvature radius, the high PET thermal inertia and the presence of ... Mehr lesen

Multiphysics Modeling of a Metal Foam

B. Chinè [1][3], M. Monno[2]
[1]Laboratorio MUSP, Macchine Utensili e Sistemi di Produzione, Piacenza, Italy
[2]Politecnico di Milano, Dipartimento di Meccanica, Milano, Italy
[3]Instituto Tecnologico de Costa Rica, Cartago, Costa Rica

Introduction: In metal foams production, nucleated gas bubbles expand in a heated metal in a mold, then the foam cool and solidify. Thereby energy, mass and momentum transfer mechanisms are present simultaneously in the system and must be taken into account. Metal foam (Figure 1) can be ... Mehr lesen

Battery Pack Temperature Distribution Simulation with COMSOL and MATLAB®

M. Masomtob[1], C. Schaeper[1], W. Zhou[1], D. Uwe Sauer[1]
[1]Electrochemical Energy Conversion and Storage Systems Group, Institute for Power Electronics and Electrical Drives (ISEA), RWTH Aachen University, Aachen, Germany

This work is to present an implementation of COMSOL with MATLAB® [1] for the liquid cooling system of a battery pack based on the physics in COMSOL. The m.file of a model of battery module from COMSOL 4.2 is exported and modified to run in MATLAB®, as well as is managed by using another ... Mehr lesen

Erste

1121–1128 of 1284

Letzte