Veröffentlichungen und Präsentationen

Schnellsuche

Ressourcen

Whitepaper

Sehen Sie, wie die Multiphysik-Simulation in verschiedenen Branchen eingesetzt wird

Multiphysik-Modellierung und -Simulation treiben Innovationen in Industrie und Wissenschaft voran – wie die zahlreichen Anwendungsbeispiele zeigen, die jedes Jahr in den Fachbeiträgen und Postern von Ingenieuren, Forschern und Wissenschaftlern auf der COMSOL Conference vorgestellt werden. Lassen Sie sich von den unten aufgeführten aktuellen Beiträgen inspirieren oder nutzen Sie die Schnellsuche, um eine bestimmte Präsentation zu finden oder nach Anwendungsbereich oder Konferenzjahr/-ort zu filtern.

Sehen Sie sich die Kollektion für die COMSOL Conference 2024 an

Suchbegriff:

Simulation of Dynamic Thermal Fields Assisting DMLS Additive Manufacturing of Biocompatible Ti-Alloy

E. Lacatus [1], G. C. Alecu [2], M. Sopronyi [3],
[1] Polytechnic University of Bucharest, Bucharest, Romania
[2] Groupe Renault, Bucharest, Romania
[3] National Institute for Laser, Plasma and Radiation Physics (INFLPR), Magurele, Romania

For the complex 3D biocompatible metallic parts, with high level of customization, used in medical prosthesis and implants Direct Metal Laser Sintering (DMLS) and Selective Laser Melting (SLM) are the most common Additive Manufacturing technologies used nowadays. However, both ... Mehr lesen

Melting and solidification behavior of PCM embedded in metal foam

Mohamed Moussa EL IDI¹, Mustapha KARKRI¹
¹Université Paris Est, CERTES.

In this paper, a numerical study is conducted on the melting and solidification process of metal foam/paraffin wax with cyclic heating and cooling. A mathematical model based on the Brinkman-Frochheimer extended Darcy equation and the local thermal non-equilibrium model (LTNE) is ... Mehr lesen

Using COMSOL Multiphysics® for the Development of an Arc Synchronous Motor with a Halbach Wheel Rotor

R. Anderka[1], A. Jocas[1], A. Vasudevan[1]
[1]University of Edinburgh, United Kingdom

Hyperloop is a theoretical high-speed mass transportation system which aims to increase efficiency through the use of low-pressure tunnels and contactless propulsion. The University of Edinburgh’s Hyperloop Team (HYPED) has been selected to participate in the SpaceX Hyperloop Pod ... Mehr lesen

The Fabrication of a New Actuator Based on the Flexoelectric Effect

S. Baskaran[1], S. Thiruvannamalai[1], N. Ramachandran[1], F.M. Sebastian[1], and J.Y. Fu[1]
[1]State University of New York at Buffalo, Buffalo, New York, USA

This paper presents a novel methodology towards the design, analysis, and the fabrication process involved in developing a cost effective method to create a piezoelectric actuator by means of the flexoelectric effect. The basic physical equations of the flexoelectric effect and the ... Mehr lesen

Frequency Dependent UEP Signatures of Naval Vessels Modeled by a Current Dipole

C. Broecheler [1], Ch. Thiel [1], A. Rennings [1], F. Ludwar [2], J. Doose [2], D. Erni [1],
[1] General and Theoretical Electrical Enigneering (ATE), University of Duisburg-Essen, and CENIDE-Center for Nanointegration Duisburg-Essen, Duisburg, Germany
[2] Technical Center for Ships and Naval Weapons, Naval Technology and Research (WTD71), Eckernförde, Germany

The underwater electric potential (UEP) signature of naval vessels poses a severe threat as it is detectable by advanced sea mines. The signature depends also on the environment, mainly the water-seabed interface, leading in summary to the total UEP signature. The seabed has a ... Mehr lesen

The Proximity Effect: A Comparison of COMSOL Multiphysics® and Analytic Solutions

C. Cooke[1], L. Shatz[2]
[1]Massachusetts Institute of Technology, USA
[2]Suffolk University, USA

An important attribute for numerical simulations is to provide accurate quantified solution values. Thus it is useful to find complex problems with analytic solutions to confirm the numerical results obtained from software. The well-known proximity effect causes a redistribution of ... Mehr lesen

Modeling and Experimental Verification of the Power Transfer and Thermal Characteristics of Piezoelectric Transformers Subjected to Combined Mechanical and Electrical Loading

S. Tuncdemir[1], W.M. Bradley[2]
[1]Solid State Ceramics, Williamsport, PA, USA
[2]QorTek, Williamsport, PA, USA

A piezoelectric transformer allows purely mechanical transfer and scaling of electrical energy via simultaneous utilization of both the direct and converse piezoelectric effects. This mechanical energy transfer enables a wide range of functional differences from typical magnetic-based ... Mehr lesen

Periodic Near-field Enhancement on Metal-Dielectric Interfacial Gratings at Optimized Azimuthal Orientation

M. Csete[1,2], X. Hu[1], A. Sipos[2], A. Szalai[2], A. Mathesz[2], and K. Berggren[1]

[1]Research Laboratory of Electronics, Nanostructures Laboratory, Massachusetts Institute of Technology, Massachusetts, USA
[2]Department of Optics and Quantum Electronics, University of Szeged, Szeged, Hungary

The effect of plasmon-wavelength scaled gratings on the surface plasmon resonance is studied experimentally and theoretically. The model samples are multi-layers containing laser fabricated gratings at bimetal-polymer interfaces. Dual-angle dependent surface plasmon resonance ... Mehr lesen

3D Modeling of Transformation Optics based Flattened Luneburg Lens Using the COMSOL Multiphysics® Software

S. Biswas [1], M. S. Mirotznik [1],
[1] University of Delaware, Newark, DE, USA

Three-dimensionally varying flattened Luneburg Lens structure whose axisymmetric invariance of material parameters is calculated by conformal mapping, presents a numerical challenge for three dimensional modelling. To address this problem, conventionally a two dimensional quasi-conformal ... Mehr lesen

Development of Eddy Current Probe using FEM for Matte Level Detection in Pyrometallurgical Furnaces

A. Saleem [1], P. R. Underhill [1], D. Chataway [2], T. Gerritsen [2], A. Sadri [2], T. W. Krause [1],
[1] Department of Physics and Space Science, Royal Military College of Canada, Kingston, ON, Canada
[2] Hatch Ltd., Mississauga, ON, Canada

Pyrometallurgical furnaces are used to produce metals such as copper, nickel and platinum by the smelting process. During smelting, the undesired material components are separated from the desired metal resulting in the formation of a slag and matte/metal phase. The slag phase ... Mehr lesen

Erste

631–640 of 1172

Letzte