Veröffentlichungen und Präsentationen

Schnellsuche

Ressourcen

Whitepaper

Sehen Sie, wie die Multiphysik-Simulation in verschiedenen Branchen eingesetzt wird

Multiphysik-Modellierung und -Simulation treiben Innovationen in Industrie und Wissenschaft voran – wie die zahlreichen Anwendungsbeispiele zeigen, die jedes Jahr in den Fachbeiträgen und Postern von Ingenieuren, Forschern und Wissenschaftlern auf der COMSOL Conference vorgestellt werden. Lassen Sie sich von den unten aufgeführten aktuellen Beiträgen inspirieren oder nutzen Sie die Schnellsuche, um eine bestimmte Präsentation zu finden oder nach Anwendungsbereich oder Konferenzjahr/-ort zu filtern.

Sehen Sie sich die Kollektion für die COMSOL Conference 2024 an

Suchbegriff:

Heat Transfer and Phase Change

Single-Phase Modeling in Microchannel with Piranha Pin Fin

X. Yu [1], C. Woodcock [1], Y. Peles [2], J. Plawsky [1],
[1] Rensselaer Polytechnic Institute, Troy, NY, USA
[2] University of Central Florida, Orlando, FL, USA

Microchannel has shown potential to dissipate high heat flux in past years [1][2]. At the same time, liquid cooling attracts more and more attention from researchers for its favorable thermal properties and ability to cool down hot and keep acceptable system temperature [3][4][5]. This ... Mehr lesen

Simulation of the Cooling and Phase Change of a Melt-Cast Explosive

W. Sanhye [1], C. Dubois [1], P. Pelletier [2], I. Laroche [2],
[1] Department of Chemical Engineering, École Polytechnique de Montréal, Montréal, QC, Canada
[2] General Dynamics Ordnance and Tactical Systems-Canada Inc., Repentigny, QC, Canada

Introduction Numerical modeling of melt-casting is becoming a popular tool for the energetic materials and explosives industry. Compared to traditional metal casting, the cooling cycle for explosive melts is significantly longer because of their high Prandtl numbers [1]. Improving the ... Mehr lesen

Design of Solar Thermal Dryers for 24-hour Food Drying Processes

F. S. Alleyne [1], R. R. Milczarek [1],
[1] Healthy Processed Foods Research Unit, U.S. Department of Agriculture, Albany, CA, USA

Solar drying is a ubiquitous method that has been adopted for many years as a food preservation method. Most of the published articles in the literature provide insight on the performance of solar dryers in service but little information on the dryer construction material selection ... Mehr lesen

Design, Simulation, and Fabrication of Thermal Angular Accelerometers

H. Alrowais [1],
[1] School of Electrical and Computer Engineering, Georgia Institute of Technology, Atlanta, GA, USA

This abstract introduces a sensor design for detecting angular acceleration in a single plane using thermal convection. The working principal of the device is based on probing temperature profile changes along a micro-torus caused by angular acceleration. By properly choosing the ... Mehr lesen

CFD Analysis of a Printed Circuit Heat Exchanger

K. Wegman [1], X. Sun [1],
[1] Department of Mechanical and Aerospace Engineering, Ohio State University, Columbus, OH, USA

In this experiment, the performance of a Printed Circuit Heat Exchanger (PCHE) was studied using COMSOL Multiphysics® software. PCHEs are diffusion bonded heat exchangers containing semicircular, chemically etched flow paths. Helium was used as the working fluid on both the hot and cold ... Mehr lesen

Modeling of Stockton University Geothermal System Using COMSOL Multiphysics® and the Subsurface Flow Module

M. Sharobeam [1], S. Pal [1], G. Villanuna [1],
[1] School of Natural Sciences and Mathematics, Stockton University, Galloway, NJ, USA

Stockton University has one of the largest closed loop geothermal system in North America. It provides heating and cooling for the university academic facilities. The well field comprises of a grid of four hundred wells bored to a depth of 130m. The ground is composed of three aquifers ... Mehr lesen

2D Axisymmetric Temperature Profile Modeling of a Delayed Coking Drum During Pre-Run Warm Up

P. H. A. Valenca [1], A. Waturuocha [1], K. Wisecarver [1],
[1] Russell School of Chemical Engineering, University of Tulsa, Tulsa, OK, USA

Delayed Coking is a refining process, which takes heavy petroleum residue as a feed. A 2D axisymmetric stationary model was created to simulate this pre-run condition with nitrogen gas, as an attempt to calibrate the model before simulating with an oil residue. The single-phase laminar ... Mehr lesen

Heat Transfer and Phase Change Simulation in COMSOL Multiphysics® Software

N. Huc [1]
[1] COMSOL France, Grenoble, France

This session is devoted to phase change modeling in heat transfer simulations. The great interest in phase change comes from the outstanding thermal performance that it enables in particular for cooling or thermal protection applications. Alternatively, phase change can induce most of ... Mehr lesen

Erste

921–928 of 1284

Letzte