Sehen Sie, wie die Multiphysik-Simulation in Forschung und Entwicklung eingesetzt wird
Ingenieure, Forscher und Wissenschaftler aus allen Branchen nutzen die Multiphysik-Simulation, um innovative Produktdesigns und -prozesse zu erforschen und zu entwickeln. Lassen Sie sich von Fachbeiträgen und Vorträgen inspirieren, die sie auf der COMSOL Conference präsentiert haben. Durchsuchen Sie die untenstehende Auswahl, verwenden Sie die Schnellsuche, um eine bestimmte Präsentation zu finden, oder filtern Sie nach einem bestimmten Anwendungsbereich.
Sehen Sie sich die Kollektion für die COMSOL Conference 2023 an
Numerical Heat Transfer Analysis of a Phase Change Material (PCM) - Enhanced Plaster
A time-dependent study was conducted using COMSOL Multiphysics® (Conjugate Heat Transfer interface and Heat Transfer with Phase Change feature) for the numerical investigation of the thermal performance of novel Phase Change Material (PCM)-enhanced plasters for their incorporation in ... Mehr lesen
Numerical Simulation of Vibrationally Active Ar-H2 Microwave Plasma
Microwave discharges have a wide range of applications, such as gas conversion, material processing and surface treatment; also they can provide an efficient way for dissociation of molecular gases as CO2 and N2O. Depending on the operating pressure and temperature, non-equilibrium ... Mehr lesen
Simplified CFD Modeling of Air Pollution Reduction by Means of Greenery in Urban Canyons
As known, air quality in urban areas is dramatically affected in particular by the noteworthy presence of respirable suspended particulate matter (such as PM2.5), nitrogen oxides (NOx), carbon monoxide (CO) and hydrocarbons (HC), which are mainly due to traffic-induced emissions. On the ... Mehr lesen
Modeling Ex Vivo Microwave Hyperthermia of Different Biological Tissues
Electromagnetic and thermal simulations are achieved using COMSOL Multiphysics® with 2D axisymmetrical finite–element method for a percutaneous microwave hyperthermia system with ex–vivo experiments on different biological tissues. Temperature variation and distribution are studied in ... Mehr lesen
Modeling Bio-Sensing Functionalized Graphene Building Blocks under Environmental Stimuli
Successive studies on graphene, reactive-edge graphene, and pore functionalized graphene were conducted throughout the use of the extended capabilities of COMSOL Multiphysics® modules, modeling and simulating the activation of functionalized building-blocks made of graphene and C- ... Mehr lesen
Numerical Simulation of Bank Protection Structure Deformation due to River Level Fluctuations
In this study, based on a bank protection structure engineering at Yangtze River, a 2D water-soil coupling model is established, in which the influence of water level fluctuation on groundwater seepage and soil shear strength is considered. According to the water level measured data of ... Mehr lesen
Green Walls for Sustainable Buildings and Cities: Aerodynamic Characterization of Vegetation
A wind tunnel experiment was modelled using COMSOL Multiphysics® CFD software. A k-ω coupled turbulence model was considered including the Brinkman equation for stationary air flow through a porous vegetation section. Mehr lesen
Model of Pressure Drop Separation during Aqueous Polymer Flow in Porous Media
Aqueous polymers used for enhanced oil recovery (EOR) application is considered a complex fluid. It can exhibit Newtonian and Non-Newtonian behavior depending on the velocity or the stresses that it is submitted during the flooding process. Therefore, the polymer flooding project ... Mehr lesen
Optimal Installation Configuration of Thermoelectric Generators
This paper presents a multiphysics model to the convective, conductive and radiative heat transfer for the thermoelectric modules (TEMs), which are used to convert heat flux into electrical current. The model basically consists of heat transfer in solids, heat transfer in thin shells, ... Mehr lesen
Simulation of an Immunodetection System Based on Magnetic Nanoparticles
In a first approach towards application of the magnetic frequency mixing technique to microfluidic structures, microplanar coils have to be designed along with sample reservoir. For this, a COMSOL Multiphysics® electrical model along with an analytical calculation is used in order to ... Mehr lesen