F. Lima, U. Mescheder, H. Reinecke
Hochschule Furtwangen University, Furtwangen, Baden-Wuerttemberg, Germany
Institut für Mikrosystemtechnik, Freiburg im Breisgau, Baden-Wuerttemberg, Germany
Electrodeposition has a major advantage over other methods of thin film deposition. It allows deposition at atmospheric pressure and room temperature, requiring inexpensive equipment. However, there are several parameters which can influence an electroplated metal layer quality. The current density distribution is taken into consideration. The Hull cell is an electrodeposition tank with a ...
N. Gurler, Y. Ziya Ider
Department of Electrical and Electronics Engineering, Bilkent University, Ankara, Turkey
Designing a Radio Frequency (RF) birdcage coil used in Magnetic Resonance Imaging (MRI) at high frequencies where the wavelength is comparable with the coil dimensions is a challenging task. Before construction of the coil, not only calculating the capacitance value which is necessary for the coil to resonate at the desired frequency but also geometrically modeling the coil in a 3D simulation ...
B. Hari, S. Bakalis, P. Fryer
The University of Birmingham, School of Chemical Engineering, Edgbaston, Birmingham, United Kingdom
Worldwide attention in the computational modeling and simulation of the human intestine is increasing in order to help understand its complex behavior and improve health. Computational fluid dynamics is an essential tool to understand the mechanics and transport phenomena of the human intestine, thereby advancing the diagnosis and treatment of gastrointestinal related diseases. The aim of this ...
University of Turku, Turku, FInland
An experimental LED light composed of a multi-chip LED-module, a LED driver and an efficient heat sink, was investigated using COMSOL Multiphysics software and the Heat Transfer Module. In an LED light heat is mainly generated in the LEDs but some amount of heat is generated also in the LED driver. The main target of the simulations was to resolve the junction temperatures of LEDs, the most ...
Wenger Engineering, Ulm, Germany
The ampacity of a cable depends on the cross section of its conductor. When selecting a cable design for a specific application it is of interest to choose the lowest possible conductor cross section in order to reduce material costs. Therefore an exact calculation of the ampacity is necessary (it is usually limited by the thermal resistance of the insulating cable materials). Commonly the ...
E. Licon, S. Casas, A. Alcaraz, J.L. Cortina, C. Valderrama
Universitat Politécnica de Catalunya, Barcelona, Spain
Ammonia separation from water by membrane contactor was simulated on transient state and compared with experimental data. Aqueous low concentrated solution of ammonium with high pH has been pumped inside the hydrophobic hollow fibers, acid solution in the outside part. The system is in closed loop configuration. In order to simulate the separation process, equations were developed considering ...
Numerical Aspects of the Implementation of Artificial Boundary Conditions for Laminar Fluid-Structure Interactions
C. Boeckle, P. Wittwer
University of Geneva, Geneva, Switzerland
We discuss the implementation of artificial boundary conditions for stationary Navier-Stokes flows past bodies in the half-plane, for a range of low Reynolds numbers. When truncating the half-plane to a finite domain for numerical purposes, artificial boundaries appear. We present an explicit Dirichlet condition for the velocity at these boundaries in terms of an asymptotic expansion for the ...
V. Pavelko, I. Pavelko, M. Smolyaninovs, H. Pffeifer, M. Wevers
Riga Technical University, Riga, Latvia
Catholic University Leuven, Leuven, Belgium
A problem of damage prediction in aircraft structure and its non-destructive evaluation is very important for aircraft structural health assessment. The analysis of the features of direct impact of thin-walled laminate component of aircraft was performed by COMSOL Multiphysics software. Mainly the GFRC and CFRC laminates were selected in form either thin separate plate or sandwich structure. The ...
Multiphysics Process Simulation of Static Magnetic Fields in High Power Laser Beam Welding of Aluminum
M. Bachmann, V. Avilov, A. Gumenyuk, M. Rethmeier
BAM Federal Institute for Materials Research and Testing, Berlin, Germany
The article deals with the application of the Hartmann effect in high power laser beam welding of aluminum. The movement of liquid metal in a magnetic field causes electric currents which build a Lorentz force that decelerates the original flow. The numerical model calculates the influence of a steady magnetic field on partial penetration keyhole laser beam welding of aluminum. Three-dimensional ...
L. Mongibello, N. Bianco, R. Fucci, F. Moscariello
ENEA - Italian National Agency for New Technologies, Energy and Sustainable Economic Development, Portici, Italy
DETEC - Università degli Studi di Napoli Federico II, Napoli, Italy
This work focuses on the numerical analysis conducted on the prototype sensor for the measurement of highly concentrated radiative heat fluxes, based on an inverse heat transfer method, realized at the ENEA Portici Research Center in collaboration with the DETEC department of the University of Naples Federico II. The estimates of highly concentrated radiative heat fluxes on the target surface of ...